PROSiXRPTR - Resideo Honeywell Home Wireless Encrypted Alarm Repeater (for ProSeries Control Panel)
Honeywell PROSiXRPTR Product Description:
The Resideo Honeywell Home PROSiXRPTR RF in an RF wireless receiver and a transmitter that is intended to extend the indoor range of PROSiX series devices. The PROSiXRPTR receives and alarm, status, and control messages from PROSiX series devices, and forwards these messages to the PROA7 or PROA7PLUS wireless control panel(s). The PROA7 series control panel then responds accordingly (arm/disarm the system, initiate an alarm, etc.).
Up to two PROSiXRPTR's can be added to the PROA7 series panel revision 03.591.92 or higher. Once enrolled in the panel the PROSiXRPTR can repeat any PROSiX transmitter Revision 5.0.1 or higher. It will NOT repeat signals from another repeater. If updating the panel allow 24 hous for all PROSiX transmitters to update before installing the PROSiXRPTR repeater.
Before mounting, enroll the PROSiXRPTR to verify adequate signal strength, and relocate if necessary. Once enrolled in a system, the PROSiXRPTR cannot be used with another control until it is removed from the current control. When mounting the PROSiXRPTR make sure to place it as high as possible, keeping it away from metal objects. The range of the repeater is approximately 200 feet through three walls of wood, aluminum and dry wall construction. When using a second repeater the range of the panel and sensors is more than 500 ft. line of site. When two repeaters are needed, install the PROA7 panel in the middle with repeaters on either direction of the panel.
Product Features:
- Transmits its own status, including wall and case tamper (front and rear), AC loss, low battery and RF Jam
- Status LED's Indicate RF Jam, AC/Battery Status, and RSSI (Received Signal Strength Indicator)
- RSSI indicates the signal condition between the repeater and the control
- Uses a 5VDC power supply to power the module and charge the battery
- Uses a 4.2VDC rechargeable backup battery. If the battery voltage falls below 2.6VDC, it is incapable of charging and must be replaced
- Provides a 24-hour backup rechargeable battery
- Over the air updates
- ETL listed to meet UL standards
- Up to 2 repeaters per system.
NOTE: Repeater 1 does not communicate with repeater 2.
Honeywell PROSiXRPTR Product Documents:
• Installation/Setup Guide for Resideo Honeywell Home PROSiXRPTR Wireless RF Alarm Repeater
• Quick Installation Guide for Resideo Honeywell Home PROSiXRPTR Wireless RF Alarm Repeater
• Step-by-Step Installation for Resideo Honeywell Home PROSiXRPTR Wireless RF Alarm Repeater
Honeywell PROSiXRPTR Product Specifications:
- Dimensions (L x W x D): 6.9" x 4.4" x 1.2" in (175 x 113 x 21 mm)
- Transformer Part Number: 300-10259
- Input Voltage: 100-240VAC (100 A 240 Vc.a.), 50/60 Hz
- Operating Voltage: 5VDC (5 Vc.c.) (1 A)
- Battery/Pile: N/P 300-10342
- Operating Temperature: 32°F to 140°:F (0°C to 60°C)
NOTE: Charging the lithium battery stops when temperature is below 32°F (0°C) - Relative Humidity: 95% non-condensing
- Acceptable Cable Size: 18 to 22 AWG
- Approvals: UL 985:2015 Ed.6+R:12Jul2018
UL 1023:2017 Ed.7
UL 1610: 2016 Ed.4
UL 1637:2017 Ed.5
UL 2017:2008 Ed.2 +R:17Jan2016
ULC S304:2016 Ed.3 +R:10Oct2018
ULC S545:2002 Ed.2
ULC Subject C1023:1974 Ed.1
CSA C22.2#205:2017 Ed.3
CAN/ULC-S540
Chapter 29, ANSI/NFPA 72
CSA C22.1 Part 1
CAN/ULC S302
CAN/ULC S301
Honeywell PROSiXRPTR Product Compatibility:
• 300-10259
• 300-10342
• PROA7CN
• PROA7PLUS
• PROA7PLUSCN
• PROA7
• SiXRF
