PROSiXC2W - Resideo Honeywell Home Hardwired-to-Wireless Encrypted Security Sensor Translator (for ProSeries Control Panels)
ProSeries PROSiXC2W Product Description:
The Resideo Honeywell Home PROSiXC2W is a Hardwired-to-SiX Wireless Converter that enables retrofitting existing 12-volt security systems by converting their wired sensors to SiX wireless technology. The PROSiXC2W converter is compatible with the ProSeries PROA7, ProSeries PROA7C, ProSeries Canada PROA7CN, ProSeries PROA7PLUS, ProSeries PROA7PLUSC or ProSeries Canada PROA7PLUSCN all-in-one wireless touchscreen control panels. Converting existing wired zones to wireless saves on installation cost, time and materials since there is no need to replace wired devices with individual transmitters.
The PROSiXC2W provides 8 hardwired zones with end-of-line resistor protection. You can use the PROSiXC2W with existing door/window contacts, motion detector PIRs, glassbreaks and other 12V sensors. Please note, the PROSiXC2W is not for use with fire, heat or CO sensors. It is recommended that any existing smoke, heat or CO detectors be replaced with new SiX-Series detectors. Only two devices may be powered using the auxiliary output on the PROSiXC2W. It provides 24-hour battery backup (4-hour if external devices are connected).
The converter will immediately send a power loss signal to the controller in the event the power is lost. When no battery is connected to the PROSiXC2W, a low battery message sends to the control panel. Also, when the battery is connected, and if battery voltage drops below 3.6VDC, a low battery message sends to the control panel. When only the battery is connected, and if the battery voltage is 3.4VDC, the system shuts down.
In addition, the PROSiXC2W can be used in new construction installations that have been fitted with hardwired systems. The PROSiXC2W is simple to install and extremely flexible. It can power wired PIRs, and the included power supply is backup up with a standard rechargeable battery. One button calibration automatically configures PROSiXC2W by learning what zones are in use. The setup of the converter is a three step process. First, mount and wire the module. Next, calibrate/activate the module zones. Lastly, enroll the module's wireless zones into the control panel.
The calibration process enables the PROSiXC2W to learn what zones are to be active and what value EOL resistors are used. The zone wiring and connections must be completed before calibration. If there is an existing resistor, it must have a value between 1K and 10K. The unit comes with eight (8) 2.2K resistors for zones that don't have one. Unused zones that are open are not recognized and reported. Before beginning, ensure all zones are connected and not faulted. During calibration, if the PROSiXC2W loses both AC and battery backup power, the zone calibration data is retained. Once the converter is calibrated, any change in the zone resistance will result in the module having to be re-calibrated again.
After enrolling, verify adequate signal strength by conducting a sensor test with the device in its intended mounting location. Adjust the device location and orientation as necessary. Once enrolled in a system, the PROSiXC2W cannot be used with another controller until it is removed from the current controller. If the device is enrolled in a panel different than the intended panel, and you are unable to delete it from the unintended panel, reset default the device to factory default setting. This procedure is available for 24 hours after enrollment with a panel and the device remains powered (battery installed).
The PROSiXC2W reports to the control panel if a low battery or tamper condition exists on the module. This is shown as a trouble on the control. The first battery test occurs 1 hour after power up. To quickly verify a good backup battery, unplug and then plug back in the power supply; the system will perform a battery test within 1 minute. The maximium distance between the power supply and PROSiXC2W is as follows; #18 wire gauge has 350 ft. wire length, #20 wire gauge has 200 ft. wire length, #22 wire gauge has 125 ft. wire length. All zones must have an EOL resistor.
Product Features:
- Reduce installation cost, time and material
- 8 hardwired zones with end-of-line resistor protection
- One-button calibration/activation of zone inputs
- Automatic zone configuration
- SiX technology MAC ID numbers are automatically assigned to activated zones
- Power supply included to power PIRs. 12V 4Ah battery provides four hours of standby. Low battery supervision and notification.
- Case and wall tamper switches
- Complete supervision of transmitters, zone tampers and low battery
- Module can be mounted next to the control panel being replaced, or relocated if necessary to maximize wireless range
ProSeries PROSiXC2W Product Documents:
• ProSeries PROSiXC2W Hardwired-to-SiX Wireless Converter - Data Sheet
• ProSeries PROSiXC2W Hardwired-to-SiX Wireless Converter - Installation and Setup Guide
• ProSeries PROSiXC2W Hardwired-to-SiX Wireless Converter - Quick Installation Guide
• ProSeries PROSiXC2W Hardwired-to-SiX Wireless Converter - Summary of Connections
ProSeries PROSiXC2W Product Specifications:
- Dimensions (L x W x D): 7.0" x 4.5" x 1.5" (178mm x 114mm x 38mm)
- Compatibility: All ProSeries control panels
- Zone Resistance: 1K up to 10K (Auto-sensing)
- Frequency: 2.4 GHz
- Power Requirements/Battery: 5VDC
- Auxiliary Power: 12VDC/100mA
- Battery Backup: Yes
- Power Supply: P/N 300-10259
- Input Voltage: 100-240 VAC, 50-60 Hz
- Operating Voltage: 5VDC
- Maximum Transformer Distance: 9.8 ft. (3m)
- Voltage Output: 12 VDC @ 100mA (Up to three sets of 20-24 gauge wiring)
- Battery/Pile: P/N 300-10342
- Operating Temperature: 32° to 122° F (0° to 50° C)
- Operating Humidity: 95% max. (Agency Compliance 93% max.) non-condensing
- Mounting Hardware: Double stick tape and screws
- Zone Resistance: 1K to 10K Ohm EOL Resistors
- Zone Wiring: 1,000ft (each zone)
- Radio Frequency: Transmission range 300 ft. (91.5m)
- LED Status Indicators: Input power
- Input Zones (Eight Hardwired): All zones that are used must have an EOL resistor
- Approvals: FCC/IC, ETL US Listed to UL 1023, cETL Listed to ULC-C1023, RoHS
- Authorized Countries: US, Canada, Latin America
* Range can vary depending on building construction, wireless interference, and other factors.
ProSeries PROSiXC2W LED Status Lights:
- LED #1 (Green) - Blinks once upon RF signal transmission (HW zone trigger/tamper and/or fault message) and a slow blink for a cover tamper
- LED #1 (Green) - Quickly blinks during the enrollment/deletion process
- LED #2 (Red) - Blinks 1s/1s off when module needs calibrating
- LED #3 (Green) - Steady on when the module has been calibrated
- LED #4 (Green and Red) - Green: 5VDC power from the plug-in transformer is present | Red (blinking 1 sec on /1 sec off @ 1 Hz each): Running on battery, DC power not present
