PG9933 - DSC Wireless Encrypted Carbon Monoxide Detector (for PowerG Control Panels)
DSC PG9933 Product Description:
The DSC PG9933 is a wireless PowerG carbon monoxide detector that provides eary warning, to protect people from the silent threat of carbon monoxide poisoning. The PG9933 is designed to monitor the CO gas level in residential dwellings and give early warning before dangerous levels are detected. This device is intended to be used with a compatible PowerG wireless alarm systems. The detector consists of an electrochemical carbon monoxide sensor assembly coupled to a wireless transmitter.
Leveraging innovative PowerG technology, and equipped with a sophisticated electrochemical sensor, this high-performing PG9933 activates visual and audio alarm indicators on the detector itself, before dangerous CO levels are reached. It also initiates an alarm via the security system, for onsite assistance, and to warn endusers who may not be home. The PG9933 CO detector communicates with the control panel and can send alarm, tamper and battery condition messages to the system receiver.
Selecting a suitable location is critical for the CO detector. The Consumer Product Safety Commission (CPSC) recommends to use at least one CO detector per household, located as near as possible to sleeping areas of the home, because the human body is most vulnerable to the effects of CO gas during sleeping hours. And, the alarm shall be heard from all sleeping areas.
For added protection, install additional CO detectors in every bedroom and on every level of your home. If your bedroom hallway is longer than 14 meters (40 feet), install a CO detector at BOTH ends of the hallway. Install an additional detector 6 meters (20 feet) away from the furnace or fuel burning heat source. For maximum protection, the detector should also be located outside primary sleeping areas or at each level of your home. Mount the detector on a firm wall or ceiling.
Product Features:
- Provides early warning of carbon monoxide poisoning, before potentially dangerous levels are reached
- Ensures reliable performance, with robust, industry-leading PowerG commercial grade wireless technology
- Precisely detects CO gas levels with sophisticated electrochemical sensing technology
- Alerts people onsite by triggering the built-in 85db alarm buzzer and large flashing LED light when CO is detected
- Extends value and performance with a long-life lithium battery, included
- Backed by DSC's 1-year limited manufacturer's warranty
DSC PG9933 Product Specifications:
- Dimensions: 4.9" x 1.9" in (125.3mm x 48mm)
- Weight (including battery): 197g (7 oz)
- Communication Protocol: PowerG
- End of life: 5 years (see date stamped on back of detector)
- Operating Frequency: 915 MHz
- Audible signal (temporal 4 tone): 85 dBA min. in alarm (at 10 ft (3 m))
- Operating Current: 16µA
- Operating Temperature (PG9936): 40°F to 100°F (4.4°C to 37.8°C)
- Humidity: 15 to 93% RH non condensing
- Transmitted Messages: CO gas alarm, low battery, tamper, trouble message as a result of sensor end of life or sensor trouble, supervision
- Power Source: One 3-volt CR123A Panasonic lithium battery (included)
- Battery Supervision: Automatic transmission of battery status data as part of any transmitted message.
- Battery Life Expectancy: Minimum 1 year. NOTE: Constant exposure to temperature or humidity extremes may reduce battery life
- Low Battery Threshold: 2.85 V
- Compatible Receivers: HSM2HOST9, HS2LCDRF(P)9, HS2ICNRF(P)9, PG9920, WS900-19, WS900-29 (912 MHz to 919 MHz)
- Approvals: FCC/IC, UL/ULC, CNC
DSC PG9933 Product Documents:
• DSC PG9933 Wireless PowerG Carbon Monoxide Detector - Datasheet
• DSC PG9933 Wireless PowerG Carbon Monoxide Detector - Installation and Operation Guide
DSC PG9933 LED Indicators:
Visual Status Indications:
- Normal: LEDs - Green flash every 12 seconds; Sounder - Off; Radio Signaling - Normal (none)
- Alarm/Test: LEDs - Red flash every 12 seconds; Sounder - ANSI S3.41 temporal 4 (press button to hush for 5 minutes); Radio Signaling - Alarm
- Detector Trouble: LEDs - Yellow flash every 6 seconds; Sounder - One 100 ms chirp every 45 seconds; Radio Signaling - Fault
- Low Battery: LEDs - Yellow flash every 12 seconds; Sounder - One 100 ms chirp every 45 seconds (press button to hush for 12 hours); Radio Signaling - Low battery
- Detector End of Life: LEDs - Yellow flash every 23 seconds; Sounder - Two chirps every 45 seconds; Radio Signaling - Fault
- Power-up: Red, yellow, green, flash sequence; Sounder - One chirp at the end of the power-up sequence
- Tamper: Green, yellow, red flash sequence every 12 seconds; Sounder - off; Radio Signaling - Tamper
DSC PG9933 Product Compatibility:
- DSC Iotega Control Panels
- DSC PowerSeries Neo Control Panels
- DSC PowerSeries Pro Control Panels
- Qolsys IQ Panel 2 Plus Control Panels
- Qolsys IQ Panel 4 Control Panels
- Qolsys IQ Hub Control Panels (Model Numbers: QS9301-0208-840, QS9302-0208-840)
- Qolsys IQ4 Hub Control Panels (Model Number: IQPH054)
