PG9920 - DSC Wireless Encrypted Alarm Repeater (for PowerG Control Panels)
DSC PG9920 Product Description:
The DSC PG9920 is a wireless PowerG repeater that relays digital data between wireless PowerG control devices and a PowerG control panel. The PG9920 repeater extends the wireless reach of the system by relaying transmissions to devices that would normally be outside the range of the control panel. The PG9920 will tramsit the following service messages to the system; AC fail, tamper, low battery, supervision and end of life.
Product Features:
- PowerG robust industry leading commercial grade wireless technology
- Visible link quality indicator on device
- 109dB Siren with Strobe Light
- Siren sounds for Fire, Carbon Monoxide, Burglary and Flood Events
- Long-life lithium batteries
- Backed by DSC's 1-year limited manufacturer's warranty
DSC PG9920 Product Specifications:
- Dimensions: 6-7/16" x 6-7/16" x 1-3/4" in (161 x 161 x 50 mm)
- Weight (including battery): 470g (16.5 oz)
- Communication Protocol: PowerG
- Backup Battery: 4.8 Volt 1300 mAh NiMH rechargeable
- Frequency Band (MHz): CE Listed PG4920: 433MHz; CE/EN listed PG8920: 868MHz; FCC/IC/UL/ULC listed PG9920: 912-919MHz
- Operating Temperature: -10°C to 55°C
- Relative Humidity: Up to 93%
- AC Power Supply (AT to AC Adapter): 120 VAC, 60 Hz / 9 VAC, 0.35 A min. (in the USA)
230 VAC, 50 Hz / 9 VAC, 0.35 A min. - Low Battery Threshold: 4.8 V
- Power Supply: Type A
- Time to charge: 80% (12 hrs)
- Low Voltage Alarm: 4.8 V
- Nominal Current Drain (when using external AC power): 100mA
- Battery Backup Duration (with fully charged 1300 mAh battery): 48 hours
- LED indicator: Green LED lights when AC power on
- Compatible Receivers: 433MHz Band: HS2HOST4; HS2LCDRF(P)4; HS2ICNRF(P)4; PG4920
868MHz Band: HSM2HOST8, HS2LCDRF(P)8; HS2IC-NRF(P); PG8920
912-919MHz Band: HSM2HOST9, HS2LCDRF(P)9; HS2IC-NRF(P)9; PG9920 - Approvals: FCC/IC, UL/ULC, CNC
DSC PG9920 Product Documents:
• DSC PG9920 Wireless PowerG Range Repeater - Datasheet
• DSC PG9920 Wireless PowerG Range Repeater - Installation and Operation Guide
DSC PG9920 LED Strength Indicators:
Visual Signal Strength:
- Green LED Blinks: STRONG
- Orange LED Blinks: GOOD
- Red LED Blinks: POOR
- No blinks: No Communication
Only GOOD or STRONG signal strengths are acceptable. If you receive a POOR signal from the device, re-locate it and re-test until a GOOD or STRONG signal is received.
DSC PG9920 Product Setup:
- Do NOT locate this product where persons will walk on the secondary circuit cables
- Do NOT use extension cords to plus in the Power Supply of this equipment
- AVOID setting up the equipment near heaters, air conditioners, ventilators, and/or refrigerators
- Do NOT connect the RF Repeater to electrical outlets on the same circuit as large appliances
- Do NOT select a place exposes your RF Repeater to direct sunlight, excessive heat, moisture, vapors, chemicals or dust
- Do NOT install this equipment near water (e.g. bath tub, wash bowl, kitchen/laundry sink, in a wet basement or near swimming pool, etc.)
- Do NOT install this equipment and its accessories in areas where there is a risk of explosion
- Do NOT connect this equipment to electrical outlets controlled by wall switches or automatic timers; avoid interference sources
DSC PG9920 Product Compatibility:
- DSC Iotega Control Panels
- DSC PowerSeries Neo Control Panels
- DSC PowerSeries Pro Control Panels
- Qolsys IQ Panel 2 Plus Control Panels
- Qolsys IQ Panel 4 Control Panels
- Qolsys IQ Hub Control Panels (Model Numbers: QS9301-0208-840, QS9302-0208-840)
- Qolsys IQ4 Hub Control Panels (Model Number: IQPH054)
